Solar Charge Regulator
Solar charge controller MPP 250 Duo Digital
MPP solar controller for high quality motorhomes, caravans and boats. Votronic solar controllers of the series "MPP" (Maximum-Power-Point) with "IU1oU2" charging characteristic are connected as a link between solar panel(s) and battery(ies). With MPP technology, the controller continuously and automatically determines the maximum power point (MPP) of the solar panels several times per second. It then transforms the excess voltage of the solar module to a higher charging current for the battery (realized by high frequency switching controller technology with high efficiency). This charging current gain ensures shorter charging times and the best possible power utilization of the solar system. The MPP solar controllers are fully automatic, maintenance free and offer the following functions: MPP charge current increase compared to conventional controllers by 10% to 30% (efficiency > 95%) due to the use of the latest controller technology (microprocessor). The increase in performance is particularly noticeable during the cooler seasons and, for example, during periods of high snow, low and diffuse lighting (hibernation). For charging lead-gel, lead-AGM, lead-acid batteries or LiFePO4 complete batteries (with integrated BMS, balancing, safety circuit and approval!) of the specified nominal voltages and the co-supply of consumers connected to these batteries in permanently installed systems with the specified battery capacities and charging programs. The charging voltage is free of peaks and regulated in such a way that overcharging of the batteries is excluded. Two battery charging outputs: Automatic charging of the main supply on-board battery (BORD I) and back-up charging and charge maintenance (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging. Monitoring-free charging: Standard protection against overload, overheating, reverse polarity and battery back discharge (in case of insufficient solar power e.g. dusk, night etc.). Parallel/buffer operation: Compliance with charging regulations even with simultaneous operation of loads. Overcharge protection: regulates the charging current of the battery back in case of too much solar power and full battery, ensures the highest possible state of charge of the battery in case of power consumption by immediate recharging. "IU1oU2" charging characteristic: defined charging voltage increase (U1) prevents harmful acid stratification (lead) and provides equalization charging of individual battery cells (lead and lith.), then automatic trickle charging (U2). Charging cable compensation: Voltage losses on the charging cables are automatically compensated. On-board power supply filter: problem-free parallel operation with wind and motor generators, mains chargers, alternators, etc. Measurement output for EBL, possibly existing electric block in the living area of the vehicle: Allows the convenient use of a (solar) current display built into the electric block to check the solar system. Please make sure to check the compatibility of your Schaudt electric block (EBL) and the corresponding control and display panel in advance, as we cannot assume any warranty for this. Switching output "AES" (only MPP 250, MPP 350 and MPP 430): Causes automatic switching of refrigerators with "AES" (Automatic Energy Selector, Electrolux / Dometic) from gas to 12 V operation in the event of permanently abundant solar power surplus. Connection for battery temperature sensor (Art.-No. 2001): In case of lead batteries, the charging voltage is automatically adjusted to the battery temperature, causes a better full charge of the weaker battery in cold weather, in summer temperatures unnecessary battery gassing and load is avoided. LiFePO4 batteries: Battery protection at high and especially at low temperatures. Highly recommended when the battery temperature may drop below 0°C during operation. Plug-ready for connection of Votronic solar display units LCD-Solar Computer S for optimal control of the system.
Solar charge controller MPP 250 Duo Digital
MPP solar controller for high quality motorhomes, caravans and boats. Votronic solar controllers of the series "MPP" (Maximum-Power-Point) with "IU1oU2" charging characteristic are connected as a link between solar panel(s) and battery(ies). With MPP technology, the controller continuously and automatically determines the maximum power point (MPP) of the solar panels several times per second. It then transforms the excess voltage of the solar module to a higher charging current for the battery (realized by high frequency switching controller technology with high efficiency). This charging current gain ensures shorter charging times and the best possible power utilization of the solar system. The MPP solar controllers are fully automatic, maintenance free and offer the following functions: MPP charge current increase compared to conventional controllers by 10% to 30% (efficiency > 95%) due to the use of the latest controller technology (microprocessor). The increase in performance is particularly noticeable during the cooler seasons and, for example, during periods of high snow, low and diffuse lighting (hibernation). For charging lead-gel, lead-AGM, lead-acid batteries or LiFePO4 complete batteries (with integrated BMS, balancing, safety circuit and approval!) of the specified nominal voltages and the co-supply of consumers connected to these batteries in permanently installed systems with the specified battery capacities and charging programs. The charging voltage is free of peaks and regulated in such a way that overcharging of the batteries is excluded. Two battery charging outputs: Automatic charging of the main supply on-board battery (BORD I) and back-up charging and charge maintenance (max. 1 A) of the vehicle starter battery (Start II) with protection against overcharging. Monitoring-free charging: Standard protection against overload, overheating, reverse polarity and battery back discharge (in case of insufficient solar power e.g. dusk, night etc.). Parallel/buffer operation: Compliance with charging regulations even with simultaneous operation of loads. Overcharge protection: regulates the charging current of the battery back in case of too much solar power and full battery, ensures the highest possible state of charge of the battery in case of power consumption by immediate recharging. "IU1oU2" charging characteristic: defined charging voltage increase (U1) prevents harmful acid stratification (lead) and provides equalization charging of individual battery cells (lead and lith.), then automatic trickle charging (U2). Charging cable compensation: Voltage losses on the charging cables are automatically compensated. On-board power supply filter: problem-free parallel operation with wind and motor generators, mains chargers, alternators, etc. Measurement output for EBL, possibly existing electric block in the living area of the vehicle: Allows the convenient use of a (solar) current display built into the electric block to check the solar system. Please make sure to check the compatibility of your Schaudt electric block (EBL) and the corresponding control and display panel in advance, as we cannot assume any warranty for this. Switching output "AES" (only MPP 250, MPP 350 and MPP 430): Causes automatic switching of refrigerators with "AES" (Automatic Energy Selector, Electrolux / Dometic) from gas to 12 V operation in the event of permanently abundant solar power surplus. Connection for battery temperature sensor (Art.-No. 2001): In case of lead batteries, the charging voltage is automatically adjusted to the battery temperature, causes a better full charge of the weaker battery in cold weather, in summer temperatures unnecessary battery gassing and load is avoided. LiFePO4 batteries: Battery protection at high and especially at low temperatures. Highly recommended when the battery temperature may drop below 0°C during operation. Plug-ready for connection of Votronic solar display units LCD-Solar Computer S for optimal control of the system.
Victron Energy SmartSolar MPPT 100/20 Solar Charge Regulator 12/24V 20A
MPPT: Ultra-fast Maximum Power Point Tracking. By continuously monitoring the voltage and current output of your solar (PV) modules, MPPT technology ensures that all available energy is actually being drawn from the modules and stored. The benefit of this is most noticeable when the sky is partially overcast and the light intensity is constantly changing. Features Suitable for 12V/24V/48V systems Short circuit proof load output Intelligent battery management with Battery Life Programmable battery charging algorithm Day/night timing and light dimming option Intelligent VE.Direct data communication port for connection with auxiliary devices such as Bluetooth Smart Dongle or GX Color Control Panel Integrated output short circuit / over temperature protection Remote monitoring and control You can remotely control and monitor the extensive features of your BlueSolar MPPT charger by attaching a Bluetooth dongle and pairing it with your smartphone or other device via VictronConnect. If your system is connected to the Victron Remote Management Internet portal (VRM) via a GX device, you have full access to your MPPT anytime, anywhere. Both VictronConnect and VRM are available free of charge. Load output Too deep discharge of the battery can be prevented by connecting all loads to the load output. The load output disconnects the loads when the battery has been discharged to a preset voltage value. Alternatively, an intelligent battery management algorithm can be selected: see Battery Life. The load output is short circuit protected. Some loads (especially inverters) are best connected directly to the battery. Inverter remote control is best connected to the load output. A special interface cable may be required, please refer to the manual. Battery Life: Intelligent battery management If the solar charge controller is not able to charge the battery to its full capacity within one day, the battery status will constantly alternate between "partially charged" and "end of discharge". This mode of operation (no regular full charging) damages a battery within a few weeks or months. The Battery Life algorithm monitors the battery's state of charge and, if necessary, raises the load disconnect threshold day by day (i.e., disconnects the load earlier) until the energy gained is sufficient to charge the battery to near 100%. From this point on, the threshold for disconnecting the load is modulated so that charging to nearly 100% is achieved about once a week. Technical data Battery voltage (automatic selection) 12V/24V/48V Nominal charging current 20A Nominal PV power 12V / 24V / 48V 290W / 580W / 1160W Max. PV open circuit voltage 100V Peak Efficiency 98% Charging algorithm multi-stage, adaptive Operating temperature range -30°C - +60°C Protection class IP43 (electronic components), IP22 (connection area) dimensions 100 x 113 x 60 mm Weight 0,65 kg
Victron EasySolar 12/1600/70-16 230V MPPT 100/50
Complete solution for solar power EasySolar combines an MPPT solar charge controller, inverter/charger and AC power distribution into a single device. Installation of the device is simple and little wiring is required. AC power distribution The AC distribution consists of a residual current circuit breaker and four AC outputs protected by fuses. One output is controlled by the AC input: it turns on only when AC power is available. PowerAssist function The unique PowerAssist technology prevents overloading of the grid or generator power supply by adding additional power through the inverter whenever necessary. Unique software for solar systems Several software programs (wizards) are available to configure the system for different grid-connected or stand-alone applications. Please refer to http://www.victronenergy.nl/support-and-downloads/software/
Victron Energy BlueSolar MPPT 100/50 Solar Charge Regulator 12/24V 50A
BlueSolar Charge Regulator MPPT Solar charge controller for 12V and 24V batteries Ultra fast Maximum Power Point Tracking (MPPT) Especially in overcast conditions when light intensity is constantly changing, an ultra-fast MPPT controller improves energy output by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Advanced Maximum Power Point detection in case of partial shading. In case of partial shading, there may be two or more maximum power points (MPP) on the current-voltage curve. Conventional MPPTs tend to settle on a local MPP. However, this may not be the optimal MPP. The BlueSolar device's innovative algorithm will always maximize energy output by adjusting to the optimal MPP. Excellent efficiency Efficient passive cooling without fans. Maximum efficiency over 98%. Utilize maximum charging current up to +40°C (104°F). Internal temperature sensor adjusts constant and charge retention voltages depending on temperature. Flexible charging algorithms Fully programmable charging algorithm (refer to software information), plus eight pre-programmed algorithms selectable via a rotary knob (refer to our manual for more details). Real-time monitoring with accessories Monitoring can be done with the appropriate accessories, either with a "ColorControl panel" or via a Bluetooth connection and a smartphone. See our range of accessories and the corresponding operating instructions.
Victron Energy BlueSolar MPPT 75/10 Solar Charge Regulator 12/24V 10A
BlueSolar Charge Regulator MPPT Solar charge controller for 12V and 24V batteries Ultra fast Maximum Power Point Tracking (MPPT) Especially in overcast conditions when light intensity is constantly changing, an ultra-fast MPPT regulator improves energy output by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Load output Deep discharge of the battery can be prevented by connecting all loads to the load output. The load output disconnects the loads when the battery has been discharged to a preset voltage value. Alternatively, an intelligent battery management algorithm can be selected: see Battery Life. The load output is short-circuit proof. Some loads (especially inverters) are best connected directly to the battery. Inverter remote control is best connected to the load output. A special interface cable may be required, please refer to the manual. Battery Life: intelligent battery management If the solar charge regulator is not able to charge the battery to its full capacity within a day, the battery status will constantly alternate between "partially charged" and "end of discharge". This mode of operation (no regular full charge) will damage a lead-acid battery within a few weeks or months.The Battery Life algorithm monitors the battery's state of charge and if necessary, day after day, raises the load disconnect threshold (i.e., disconnects the load sooner) until the energy gained is sufficient to charge the battery to near 100%. From this point, the threshold for disconnecting the load is modulated so that charging to near 100% is achieved approximately once a week. Monitoring and control The charge regulator also features a programmable battery charging algorithm and a day/night time control with light dimming option. Monitoring can be done with the appropriate accessories either with a remote control or via a Bluetooth connection and a smartphone. See our range of accessories and the corresponding instruction manuals.
Victron Energy SmartSolar MPPT 100/20 Solar Charge Regulator 12/24V 20A
SmartSolar Charge Regulator MPPT Ultra-fast Maximum Power Point Tracking (MPPT) Especially in overcast conditions when light intensity is constantly changing, an ultra-fast MPPT controller improves energy output by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Load output Battery overcharging can be prevented by connecting all loads to the load output. The load output disconnects the loads when the battery has been discharged to a preset voltage value. Alternatively, an intelligent battery management algorithm can be selected: see BatteryLife. The load output is short-circuit proof. Battery Life: intelligent battery management If the solar charge controller is not able to charge the battery to its full capacity within one day, the battery status will constantly alternate between "partially charged" and "end of discharge". This mode of operation (no regular full charge) will damage a lead-acid battery within a few weeks or months. The BatteryLife algorithm monitors the state of charge of the battery and if necessary, day by day, it raises the threshold for disconnecting the load (i.e., the load is disconnected earlier) until the energy gained is sufficient to charge the battery to near 100%. From this point on, the load disconnect threshold is modulated so that charging to near 100% is achieved about once a week. Built-in Bluetooth Smart: No dongle needed. The wireless solution for setting up, monitoring and updating the controller using Apple and Android smartphones, tablets or other devices.
Victron Energy SmartSolar MPPT 100/30 Solar Charge Regulator 12/24V 30A
SmartSolar Charge Regulator MPPTSolar charge controller for 12V and 24V batteries Ultra-fast Maximum Power Point Tracking (MPPT) Especially in overcast conditions when light intensity is constantly changing, an ultra-fast MPPT controller improves energy output by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Advanced Maximum Power Point detection in case of partial shading. In case of partial shading, there may be two or more maximum power points (MPP) on the current-voltage curve. Conventional MPPTs tend to settle on a local MPP. However, this may not be the optimal MPP. The BlueSolar device's innovative algorithm will always maximize energy output by adjusting to the optimal MPP. Excellent efficiency One cooling fan. Maximum efficiency at over 98 Flexible charging algorithms Fully programmable charging algorithm (also refer to the software page on our website) and eight pre-programmed algorithms that can be selected via a rotary knob (see our manual for more details). Comprehensive electronic protection Overheating protection and load reduction at high temperatures. PV short circuit and PV reverse polarity protection. PV reverse current protection.
Victron Energy SmartSolar MPPT 100/50 Solarladeregler 12/24V 50A
SmartSolar Charge Regulator MPPT Ultra-fast Maximum Power Point Tracking (MPPT) Especially in overcast conditions when light intensity is constantly changing, an ultra-fast MPPT controller improves energy output by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Load output Battery overcharging can be prevented by connecting all loads to the load output. The load output disconnects the loads when the battery has been discharged to a preset voltage value. Alternatively, an intelligent battery management algorithm can be selected: see BatteryLife. The load output is short-circuit proof. Battery Life: intelligent battery management If the solar charge controller is not able to charge the battery to its full capacity within one day, the battery status will constantly alternate between "partially charged" and "end of discharge". This mode of operation (no regular full charge) will damage a lead-acid battery within a few weeks or months. The BatteryLife algorithm monitors the state of charge of the battery and if necessary, day by day, it raises the threshold for disconnecting the load (i.e., the load is disconnected earlier) until the energy gained is sufficient to charge the battery to near 100%. From this point on, the load disconnect threshold is modulated so that charging to near 100% is achieved about once a week. Built-in Bluetooth Smart: No dongle needed. The wireless solution for setting up, monitoring and updating the controller using Apple and Android smartphones, tablets or other devices.
Victron Energy SmartSolar MPPT 75/15 Solar Charge Regulator 12/24V 15A
SmartSolar Charge Regulator MPPTSolar charge controller for 12V and 24V batteries Ultra-fast Maximum Power Point Tracking (MPPT) Especially in overcast conditions when light intensity is constantly changing, an ultra-fast MPPT controller improves energy output by up to 30% in comparison to PWM charge controllers and by up to 10% compared to slower MPPT controllers. Load output Battery overcharging can be prevented by connecting all loads to the load output. The load output disconnects the loads when the battery has been discharged to a preset voltage value. Alternatively, an intelligent battery management algorithm can be selected: see BatteryLife. The load output is short-circuit proof. Battery Life: intelligent battery management If the solar charge controller is not able to charge the battery to its full capacity within one day, the battery status will constantly alternate between "partially charged" and "end of discharge". This mode of operation (no regular full charge) will damage a lead-acid battery within a few weeks or months. The BatteryLife algorithm monitors the state of charge of the battery and if necessary, day by day, it raises the threshold for disconnecting the load (i.e., the load is disconnected earlier) until the energy gained is sufficient to charge the battery to near 100%. From this point on, the load disconnect threshold is modulated so that charging to near 100% is achieved about once a week. Built-in Bluetooth Smart: No dongle needed. The wireless solution for setting up, monitoring and updating the controller using Apple and Android smartphones, tablets or other devices.
The solar charge controller serves as a connector between the solar panel, a battery or other desired devices which consume the power. This allows you to control the state of charge of the battery in a very uncomplicated way. Overheating protection is built into the controller to protect the solar charge controller and the devices connected to it.
Control via app using Bluetooth provides even greater convenience when using the solar charge controller.